Open Tools · Payloadrange

Payloadrange user guide

Use Payloadrange for preliminary aircraft studies from your own data: atmosphere, climb, take-off roll, range and endurance, payload-range, balance, trim and V-n. To use the tool itself, open Payloadrange.

Professional use. Results are for education and preliminary design. They must be checked by a qualified professional, and they are not a substitute for code-compliant design or licensed engineering judgement.

Payloadrange runs preliminary aircraft performance studies in your browser from data you enter yourself: standard atmosphere, level flight and climb, take-off ground roll, range and endurance, payload-range, weight and balance, trim, reduced flight modes and a V-n envelope. It is for education and preliminary study only, not for flight planning or operational use.

Getting started

For education and preliminary studies only. Not for flight planning, operational loading, certification or safety decisions. No warranty. A qualified professional must independently verify inputs, methods and results before professional use.

Open the tool and pick a workspace on the tab row: Atmosphere, Climb, Take-off, Range, Payload-range, Balance, Trim, Modes, V-n or Cases. Each workspace has its inputs on the left and results, charts and the assumptions of the model on the right. Results recalculate as you type and never show numbers that belong to older inputs.

First calculation in two minutes:

  1. Open Climb. The inputs hold generic placeholder numbers for a light aeroplane. Replace them with your own.
  2. Read the drag, power required, excess power and climb rate. The charts show drag against speed and climb rate against speed, with the stall speed marked.
  3. Change the speed unit to knots; the number you typed is converted (to 15 significant digits) so the physical value does not change, and everything else follows.
  4. Choose Add to case sheet, open Cases, and use Export to download the case sheet as CSV. Use Save to write the whole study to a JSON file and Open to bring it back.

The Examples button opens 10 complete studies, such as a take-off on soft grass or a loading that exceeds the aft centre-of-gravity limit. All example numbers are generic illustrations and are not data for any real aircraft.

Your data, units and what is not included

Payloadrange contains no aircraft database. Every weight, area, coefficient, thrust, fuel-consumption figure, limit and station is a number you type. The tool makes no airworthiness, performance or compliance claim for any aircraft, and the placeholders you see on first opening are only there so the calculators start with something readable.

Each input has its own unit menu (metres or feet, kilograms or pounds, newtons or pounds-force, metres per second or knots, and so on). The page converts to SI before the engine runs, using the exact international definitions of the foot, pound and nautical mile. Numbers are read strictly: a comma, a unit written in the number box or a value too small to represent is refused with a message instead of being changed.

Specific fuel consumption must be mass-based: grams of fuel per kilonewton of thrust per second for a jet, or grams per kilowatt-hour of shaft power for a propeller. A figure in pounds per pound-force per hour is also accepted and converted. Do not enter a weight-based figure as if it were mass-based.

Altitude is geopotential, not geometric height. If your source gives geometric height, convert it first.

The workspaces

Atmosphere

Temperature, pressure and density of a dry standard atmosphere from 0 to 20 000 m geopotential altitude, with ratios to sea level. The charts show the temperature profile and the pressure and density ratios, with your altitude marked. This is a standard state, not weather and not a density-altitude correction.

Climb (level flight)

Enter weight, wing area, speed, air density, the drag polar (CD0 and k), CLmax and thrust at that speed. The engine balances lift with weight, then returns dynamic pressure, CL, CD, drag, lift-to-drag ratio, power required, excess power, climb rate and stall speed. Density can be typed or taken from the standard atmosphere at an altitude. If the speed is below the stall speed for your CLmax, the tool says so and still draws the curves above it. The model is straight, small-angle and subsonic.

Take-off

Ground roll from rest to a target speed with constant thrust, fixed CL and CD on the ground and rolling friction. The wheel load falls as lift builds, and the calculation is refused if the wheels would leave the ground before the target speed or the net force reaches zero. The result is the ground roll only: no wind, slope, rotation, obstacle clearance or balanced-field analysis.

Range

Cruise range and endurance for a jet or a propeller at constant speed and lift-to-drag ratio, from the initial and final mass. The chart shows range against the fuel burned. There are no reserves, climb, descent or other mission segments.

Payload-range

For each payload, the fuel on board is the smaller of the tank capacity and the mass left under your maximum take-off mass, and the reserve you enter is not burned. The engine gives the range for each payload, and the chart marks the maximum-payload point, the full-fuel point at maximum take-off mass, and the no-payload (ferry) point. It is a diagram of your assumptions, not a statement of what an aircraft can legally carry.

Balance

Up to 200 mass stations, each with a mass and an arm from one datum. The tool returns the total mass, moment and centre of gravity and checks them against the mass and CG limits you enter. The chart draws your limits as a box and the loading sequence in table order. Whether the loading is "inside the limits" refers only to the box you typed; it is not an approved loading calculation.

Trim

Enter the required lift coefficient and the linear coefficients (CL0, Cm0 and the derivatives with respect to angle of attack and elevator). The engine solves the two equilibrium equations together and reports angle of attack, elevator, both residuals and a condition estimate. Results outside the validity limits you enter are refused. Use one sign convention for every coefficient. Estimating derivatives or a static margin is outside this tool; enter numbers from a source you are entitled to use.

Modes

The roots of the 2×2 matrix [[a, b], [c, d]] you enter: real parts, imaginary part and a stability verdict, drawn in the complex plane. For an oscillation the page also shows the natural frequency, damping ratio, period and time to halve or double, computed from the roots. This is a reduced two-state model and not a full aircraft stability assessment.

V-n

The manoeuvre envelope from your lift limits and your own limit load factors, with the stall and corner speeds, plus a simple quasi-steady gust load for a gust speed and alleviation factor you choose. Gust values are omitted at speeds below the 1 g stall speed or where the gust speed exceeds one tenth of the airspeed. The load limits are numbers you enter; no regulation text is built in and no compliance is implied. There is no flutter estimate.

Files, exports and shortcuts

Save writes one JSON file with the title, the inputs and units of every workspace, the case sheet and the notices. Open reads it back and checks every field; a file with unknown fields, wrong types or a different version is refused, never repaired, and Undo restores the previous study. The study autosaves in this browser only. Files are limited to 2 MiB.

The Export menu downloads each chart as SVG or PNG, the current result as CSV, and, on the case sheet, all cases as CSV. Balance also exports the station table with your station names. Every export carries the footer "Made with Payloadrange · simulations4all.com" and the professional-use notice. CSV cells that begin with a formula character are neutralised. Print this page prints the current workspace.

Press ? for the keyboard shortcuts: undo and redo, save and open, add to the case sheet, and switching workspace with Alt and a digit. Typing in one field is one undo step; every other change is its own step. The tool works with the keyboard alone and with a screen reader: charts have text descriptions, and results are announced when they update. Light, dark and automatic themes are available, and the layout fits a phone screen.

Limits: a batch is at most 1,000 requests, a V-n envelope at most 1,001 samples, and the case sheet at most 200 cases. Result and data tables are shown 25 rows at a time, and the station editor 20.

How we verify

The Verify page runs 49 ready checks in your browser, on the same gated worker as the calculators. They fall into 9 independent families: the standard atmosphere, level-flight performance, ground roll, jet and propeller range, weight and balance, trim, flight modes and the V-n envelope. Each family is counted once however many points it samples. The expected values come from a separate generator that never imports the engine and uses different methods: numerical integration of the hydrostatic equation and of the ground-roll work, step-by-step fuel burn, exact rational arithmetic for mass and moment, and prescribed complex roots.

These are verification checks: they show the code solves its stated equations correctly. They are not validation against measured or published aircraft data. A check against a published worked example is marked PENDING SOURCE and is not counted. The badge on the Verify page appears only after a complete run in which every check passes.

1 validation entry is pending a legitimately opened published source, and no aircraft validation is claimed.

Limitations of the models

  • Straight, steady flight with a drag polar and CLmax you supply; the polar must hold at the speed you enter. No compressibility, no stall or post-stall behaviour, no steep climb.
  • Constant thrust and constant coefficients on the ground roll; no wind, slope, runway change or rotation.
  • Range and endurance at constant speed, lift-to-drag ratio and propulsion efficiency, with no fuel allowances beyond the reserve you enter in the payload-range workspace.
  • A mass and centre-of-gravity box you enter yourself, not an approved loading envelope.
  • Linear trim inside the angle limits you enter, with one pitching-moment equation.
  • A reduced two-state flight model; neutral or defective roots need separate analysis.
  • A quasi-steady gust model with a single alleviation factor; no flutter, aeroelasticity or structural analysis.

Nothing here is suitable for flight planning, operational loading, certification or any safety decision. A qualified professional must independently verify the inputs, the method and the results before any professional use.

Compared with other tools

A spreadsheet can do every calculation here, but it leaves units, regimes and silent errors to you; Payloadrange converts units explicitly, refuses states outside its model and shows the assumptions beside each result. Desktop aircraft-design packages offer geometry-based aerodynamics, engine and aircraft databases, mission optimisation, full flight dynamics, aeroelasticity and certification workflows; none of that is included here. Payloadrange is free, needs no installation, keeps your data in your browser, saves open JSON and CSV files, and lets you check its own arithmetic on the Verify page. Use it for preliminary studies, teaching and cross-checks.

Payloadrange user guide: atmosphere, climb, take-off, range, balance, trim, V-n | Simulations4All